# 4.1 with duty ratio. Analysis, the data

4.

1 SIMULATION RESULTS: Table 4.1 simulated data for torque error.TORQUE ERROR (Nm) WITHDIRECT TORQUE CONTROL TORQUE ERROR (Nm) WITH FUZZY TIME (S)0 0 00.2 0.025 10.

We Will Write a Custom Essay Specifically
For You For Only \$13.90/page!

order now

15 0.018 20.16 0.02 30.

15 0.0195 40.15 0.0195 10 Figure 4.1 Result for torque error using DTC and fuzzy logic with duty ratio.

Analysis, the data in the tablewere applied. The torque behavior of the motor using ordinary DTC and fuzzy logic with duty ratio control for a torque command of 0.15Nm with the output drive updated at a rate of 5kHz were used. The flux ripple regained was 0.

05wb (0.2-0.15)N-m greater and lesservalues with the only DTC while infuzzy logic with duty ratio control, the ripple was reduced further to 0.0055Nm(0.025-0.00195)Nm greaterand lesser value, assumed under shoot in the torque value at the starting point of each voltage vector were neglected.

Table 4.2 Data for flux linkage errorERROR IN FLUX LINKAGE (Wb) WITH DTC ERROR IN FLUX LINKAGE (Wb) WITH FUZZY TIME0 0 018 2.4 112 1.5 214 1.

7 313.33 1.733 413.33 1.

733 10 Figure 4.2 Result for flux linkage in fuzzy logic with duty ratio and DTCIllustration, datain table were used.torque response of the motor in the control for a step torque in fuzzy logic with duty ratio control and DTC for a torque command of 2.4Wb with the motor drive output updated at a rate of 5kHz were used, the ripple generated was 4.

67Wb (18-13.33)Wb greater and lesser values with ordinary DTC, while in fuzzy logic with duty ratio control, ripples was reduced further to 0.667b (2.4-1.733)Wb upper and lower values, assumed order response in flux value at starting of each voltage sector were neglected.Table 4.

3 Data for position of the stator flux linkage.ERROR IN THE POSITION OF FLUX LINKAGE WITH DTC ERROR IN THE POSITION OF FLUX LINKAGE WITH FUZZY TIME0 0 03.3 0.9 12.2 0.06 22.

5 0.07 32.45 0.0643 4 Figure 43 Result for position of stator flux linkage using DTC and fuzzy logic with duty ratio.

In the analysis, the data in the tablewere used. The position where the stator flux linkage of the motor using ordinary DTC and fuzzy logic with duty ratio control respectively for a step angular command of 3.3 degree with the drive output updated at a rate of 5kHz were used, the position where the flux linkage ripple was reduced to 0.85degree (3.3-2.

45) greater and lesser values with the ordinary DTC while in fuzzy logic with duty ratio control, the ripple wasreduced to 0.857 degree (0.9-0.0643)degreegreater and lesser values, assumed the under shoot in the flux value at the starting of each voltage sector were neglected.

4.2 DISCUSSI0NIn the analysis, the data in the tables were used. The torque, flux, and the position of the stator flux linkage responsesof the motor using ordinary DTC and fuzzy logic with duty ratio control respectively for a step torque, flux and angular command of 0.

15N¬-m, 2.4wb and 3.3 degree with the drive output updated at a rate of 5KHZ were used. The torque, flux and the position of the flux linkage space vector ripples generated were 0.

09N-m, 4.67wb and 0.85 degree approximately, while in fuzzy logic control with duty ratio, the ripples were reduced to 0.0055N-m, 0.

44wb and 0.04 degree respectively, neglecting the both under shoot at the beginning of each voltage vector. With these, we observed that the ripples were reduced drastically and able to achieve 95% of improvement.

x Hi!
I'm Gerard!

Would you like to get a custom essay? How about receiving a customized one?

Check it out